Auto Gain Compressor - HALion - 7.5

HALion Help

Product
HALion
Version
7.5
ft:locale
en-US
Document type
Webhelp
ft:openMode
fluidtopics

This effect is a dynamic range compressor that automatically adjusts the makeup gain to maintain a consistent output level. Its clipping stage prevents the amplitude of the output signal from exceeding 0 dBFS, while also providing further sound-shaping options.

In/Out Meters

Show the highest peaks of all available input and output channels.

GR Meter

Shows the amount of gain reduction.

Mode
  • Feedforward analyzes the input signal of the compressor.

  • Feedback analyzes the output signal of the compressor.

    Feedback mode results in a less direct sound, which can be perceived as more pleasant. In particular, the Attack Time behavior is less sensitive than in Feedforward mode.

Threshold

Determines the level at which compression begins. Sounds that exceed the threshold are reduced in volume, based on the Ratio setting.

Ratio

Determines by how much the signal is reduced when it exceeds the threshold. A higher ratio results in a more pronounced reduction.

Knee

This parameter allows for a more gradual onset of compression, making it less noticeable and more musical. For example, if Knee is set to 12 dB, compression starts at a value of 6 dB below the threshold, and the compression ratio increases smoothly until it reaches the specified Ratio value of 6 dB above the threshold. Without Knee, signals above the threshold are instantly compressed based on the specified Ratio value.

Intensity

At the maximum setting, gain reduction is fully applied, resulting in an aggressive sound. At lower settings, less gain reduction is applied, preserving more of the original dynamics and resulting in a smoother sound.

When used in conjunction with the Intensity parameter, lower Knee settings will work best.

Auto Gain

Determines the amount of gain compensation, which enables you to adjust the loudness. In contrast to classic makeup gain parameters, Auto Gain allows you to change parameters such as Threshold and Ratio without noticeably altering the loudness.

Output

Sets the output gain of the compressed signal after the equalizer and the clipping stage.

You can use Output in addition to Auto Gain, to trim the level before the compressed signal is blended with the dry signal via the Mix control. If Auto Gain is set to the minimum, Output acts as a classic make-up gain.

Mix

Sets the ratio between the dry and the wet signal.

Times Tab

Activate Transient Mode

Activates/Deactivates transient processing.

Transient Gain

Attenuates/Boosts the transients of the compressed signal. The transients are detected in the input signal, before the compressor, but after the side-chain filters.

Transient Time

Sets the duration of the transients.

Attack Time

Sets the attack time. This parameter determines how quickly the compressor responds to sounds that exceed the threshold. Faster attack times mean the compressor acts quickly, while slower attack times allow more of the initial sound to pass through before compression starts.

Fast Attack On/Off

With Fast Attack activated, the Attack Time is automatically shortened on loud signal impulses.

Release Time

Sets the release time. This parameter determines how quickly the compressor stops reducing the gain after the signal falls below the threshold. A longer release time means a slower return to the uncompressed signal level.

Fast Release On/Off

With Fast Release activated, the Release Time is automatically shortened when the signal gain drops rapidly.

EQ/Clip Tab

EQ On/Off

Activates/Deactivates the equalizer.

Clip On/Off

Activates/Deactivates the clipping stage.

Signals can exceed 0 dBFS if the clipping stage is deactivated.

EQ Frequency

Sets the frequency of the equalizer.

EQ Post-Clip

By default, the EQ is applied before the clipping stage in the signal flow, which means that it also affects the overtones that can be introduced by clipping. With EQ Post-Clip activated, the equalizer is placed after the clipping stage and the output of the clipping stage is filtered together with the rest of the sound.

EQ Slope

Sets the slope of the equalizer. Turning the control to the left creates a low-pass slope, which results in a darker sound. Turning the control to the right creates a high-pass slope, which results in a brighter sound.

Clip Gain

The clipping stage at the output prevents the amplitude of the signal from exceeding 0 dBFS and provides further tone shaping options. The LED indicates clipping, lighting up if the signal exceeds -0.5 dB. The amount of clipping depends on the compressor settings. Longer attack times often result in more frequent clipping, especially at transients. You can adjust the compressor settings or lower Clip Gain to achieve the desired clipping amount. You can also increase Clip Gain for more clipping.

Hard/Soft Clip

Blends between hard and soft clipping. Soft clipping sounds warmer, and is typically associated with analog clipping. Hard clipping sounds more direct, and is associated with digital clipping.

Sidechain Tab

On this tab, you can set up the sidechain filters. These filters only affect the signal that is analyzed by the compressor. You can increase or decrease the amount of compression for certain frequencies by cutting or boosting them.

Sidechain Filter On/Off

Activates/Deactivates the sidechain filters.

Monitor

Allows you to monitor the sidechain filters.

Sidechain Low Cut Frequency

Sets the cutoff frequency of the 6 dB low cut filter. Frequencies below this frequency will be damped. The low cut filter can be used to send fewer bass frequencies into the compressor sidechain, for example, to reduce modulation by the bass frequencies.

Peak Filter (Sidechain Center Frequency/Gain/Q-Factor)

Allows you to cut or boost frequencies in the sidechain. This way, the frequencies can be sent into the compressor earlier or later with regard to the set threshold.

  • Sidechain Center Frequency sets the frequency that is cut or boosted with the Gain parameter.

  • Sidechain Center Gain sets the amount of cut or boost.

  • Sidechain Center Q-Factor adjusts the bandwidth from wide to narrow. The smaller the Q-factor, the wider the bandwidth, and the more frequencies are affected.